Muratec F-565 Specifikace Strana 203
- Strana / 383
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
3-119
5. Press <Reset> to exit the test mode.
3.13.7 RTC(real time clock) Test
This test mode is not applicable to field service of this machine.
3.13.8 Page memory check
When the letters are not printed correctly, perform this test.
1. Press <Setting>, <*>, <1>, <1>, then select [Page Memory check].
2. Select the desired checking area.
3. The machine starts checking and the result (OK/NG) will be shown in the display.
If NG is shown, perform the DRAM clear (page 3-118), and then go back to step 1.
4. Press <Setting> to exit the test mode.
- MFX-2050/MFX-1450 1
- F-565/F-525 1
- Safety Information 2
- Table of contents 4
- 1 General Description 6
- 1.2 Specifications 7
- PC Print 10
- Network Scan, Scan to E-mail 24
- Internet Fax 29
- Network OfficeBridge Settings 37
- LDAP Settings 49
- Network Authentication 52
- 2 Machine Composition 54
- Original Detection 55
- 1 Reflector Tape 56
- 2.2 Recording Section 58
- 2.3 Image Processing 59
- 2.3.3 Development 60
- 2.3.4 Image Transfer 60
- LED Lamp 61
- Development 61
- Cleaning 61
- 2.3.7 Fusing 62
- See the attached files 65
- 2.5 Main Control PCB 66
- 2.7 Power Supply Unit (PSU) 68
- 2.8 Sensors 69
- 2.8.2 Sensor Descriptions 70
- 2.9.1 Port setting list 71
- Import results and errors 73
- Export details 74
- 2.9.3 LDAP 75
- Search Method 76
- LDIFDE Command 77
- Packet Analyzer 78
- 2.9.4 SNMP Setting 79
- GetRequest 80
- 2.9.5 e-mail gateway 81
- Available Methods in NGP 82
- 3 Adjustment Procedures 85
- Machine Parameter 007 89
- Machine Parameter 010 89
- Machine Parameter 011 90
- Machine Parameter 012 90
- Machine Parameter 013 91
- Machine Parameter 014 91
- Machine Parameter 015 92
- Machine Parameter 016 92
- +2.70 mm 93
- Machine Parameter 020 94
- Machine Parameter 021 94
- Machine Parameter 025 95
- Machine Parameter 030 96
- Machine Parameter 031 96
- Machine Parameter 032 96
- Machine Parameter 033 97
- Machine Parameter 034 97
- Machine Parameter 090 98
- Machine Parameter 092 98
- Machine Parameter 100 99
- Machine Parameter 101 99
- Machine Parameter 107 99
- Machine Parameter 108 100
- Machine Parameter 140 101
- Machine Parameter 141 101
- Machine Parameter 147 102
- Machine Parameter 148 102
- Machine Parameter 161 103
- Machine Parameter 160 103
- Machine Parameter 167 104
- Machine Parameter 168 104
- Adjusting the print margin 105
- Machine Parameter 180 106
- Machine Parameter 181 106
- Machine Parameter 187 107
- Machine Parameter 188 107
- Machine Parameter 220 108
- Machine Parameter 221 108
- Machine Parameter 227 109
- Machine Parameter 228 109
- Machine Parameter 240 110
- Machine Parameter 241 110
- Machine Parameter 247 111
- Machine Parameter 248 111
- Machine Parameter 285 112
- Machine Parameter 286 112
- Machine Parameter 287 113
- Machine Parameter 288 113
- Machine Parameter 289 114
- Machine Parameter 460 115
- Machine Parameter 461 115
- Machine Parameter 462 116
- Machine Parameter 463 116
- Machine Parameter 464 117
- Machine Parameter 465 117
- Machine Parameter 466 118
- Machine Parameter 467 118
- Machine Parameter 468 119
- Machine Parameter 469 119
- Machine Parameter 470 120
- Machine Parameter 471 120
- Machine Parameter 472 121
- Machine Parameter 473 121
- Machine Parameter 474 122
- Machine Parameter 475 122
- Machine Parameter 476 123
- Machine Parameter 477 123
- Machine Parameter 478 124
- Machine Parameter 479 124
- Machine Parameter 480 125
- Machine Parameter 481 125
- Machine Parameter 482 126
- Machine Parameter 483 126
- Machine Parameter 484 126
- Machine Parameter 485 127
- Machine Parameter 486 127
- Machine Parameter 487 128
- Machine Parameter 488 128
- Machine Parameter 489 128
- Machine Parameter 490 129
- Machine Parameter 492 129
- Machine Parameter 493 130
- Machine Parameter 494 130
- Machine Parameter 495 131
- 3.3 Memory Switch Adjustment 133
- Memory Switch 000 — Dialer 135
- Memory Switch 001 — Dialer 136
- Memory Switch 002 — Dialer 137
- Memory Switch 005 — Dialer 138
- Memory Switch 020 — Reception 143
- Memory Switch 021 — Reception 143
- Memory Switch 023 — Reception 144
- Memory Switch 030 — Modem 144
- Memory Switch 031 — Modem 145
- Memory Switch 032 — Modem 145
- Memory Switch 033 — Modem 146
- Memory Switch 040 — Scanner 147
- Memory Switch 070 — Operation 153
- Memory Switch 071 — Operation 154
- Memory Switch 072 — Operation 154
- 3.5 All RAM Clear 162
- 3.7 Unique Switch Adjustment 163
- Unique Switch 000 — Dialer 165
- Unique Switch 001 — Dialer 165
- Unique Switch 020 — Reception 169
- Unique Switch 021 — Reception 169
- Unique Switch 022 — Reception 170
- Unique Switch 023 — Reception 170
- Unique Switch 029 — Reception 170
- Unique Switch 030 — Modem 171
- Unique Switch 031 — Modem 171
- Unique Switch 032 — Modem 172
- Unique Switch 034 — Modem 172
- Unique Switch 037 — Modem 173
- Unique Switch 041 — Scanner 174
- Unique Switch 044 — Scanner 174
- Unique Switch 048 — Scanner 175
- Unique Switch 049 — Scanner 176
- Unique Switch 050 — Printer 177
- Unique Switch 052 — Printer 177
- Unique Switch 053 — Printer 178
- Unique Switch 070 — Operation 181
- Unique Switch 071 — Operation 181
- Unique Switch 072 — Operation 182
- Unique Switch 074 — Operation 182
- Unique Switch 076 — Operation 183
- Unique Switch 078 — Operation 183
- 3.8 T.30 Monitor 187
- NSF, NSC, NSS: 190
- CSI, CIG, TSI: 190
- DIS, DTC, DCS: 190
- 3.9 Printer maintenance mode 192
- Register the e-mail location 193
- 3.10 Monitor speaker 194
- 3.11 Test Modes 195
- 3.11.2 Printer Test 196
- 3.11.3 Feeder test 198
- 3.11.4 Port Status 198
- 3.11.5 Set Background Level 198
- 3.13 Factory Functions 199
- 3.13.2 LED Test 200
- 3.13.3 LCD Test 200
- 3.13.4 Key Panel Test 201
- 3.13.5 SRAM Check 201
- 3.13.6 DRAM Check 202
- 3.13.8 Page memory check 203
- 3.13.9 Touch panel adjustment 204
- 3.13.10 Generate bell test 204
- 3.14 Line Tests 205
- 3.14.2 Tonal Signal Test 206
- 3.14.3 DTMF Output Test 207
- 22 23 24 210
- 3.17 DRAM Clear 215
- 3.18 Clear Life Monitor 216
- 3.19 Clear Optional Data 216
- 3.20 Set Service Code 217
- 3.21 Life monitor maintenance 218
- 3.22 Sensor input test 221
- 3.23 Printer diagnostic mode 222
- 3.24 Network service mode 223
- 3.25 Multi Line Settings 225
- 3.26 Flash Rom Sum Check 227
- 3.28 Service Report 228
- 3.28.2 Clear service report 231
- 3.29 Quick Initial settings 244
- Service report settings 245
- 3.30.1 Latest version update 246
- 3.30.2 Manual update 247
- 3.31 Update the software 249
- 2. Press [Main Board] 250
- 6. Click [OK] 252
- Data are stored in memory 254
- 7. Click [Start] 255
- 3.31.4 Error code 257
- 3.32.2 Firmware Update 260
- 4 Troubleshooting Procedures 267
- Suggested corrective action: 268
- Removing jammed paper 270
- Jammed in feed area 271
- Jammed in fuser area 271
- Jammed in paper exit area 271
- Instruction 273
- 4.10.1 Dialing errors 280
- 4.10.2 Reception errors 281
- 4.10.3 Transmission errors 282
- 4.11.1 Please Call Service XX 283
- 4.12.1 Blank pages 286
- 4.12.2 Black pages 286
- • Clean the LED print head 287
- 5.2 Re/Disassemble 293
- 5.2.1 COVERS 295
- 2) Remove the TRAY DOCUMENT 296
- 3) Remove the COVER CONNECT 296
- 1) Open the Cover platen 298
- 3) Close the Cover platen 298
- 4) Open the Guide outer 298
- Cover TX side B 299
- Guide outer 299
- 1) Open the Cover ADF base 301
- 3) Close the Cover ADF base 301
- Cover front 302
- Tray exit paper 302
- Cover top 303
- Cover panel NGP 303
- Cover top PPF 303
- 1) Open the Tray A MP 304
- 5.2.2 PCBS 305
- PCB PANEL 1 306
- PCB PANEL 2 306
- PCB INVERTER (MFX-2050/1450) 307
- PCB INVERTER (F-565/525) 308
- LAMP (MFX-2050/1450) 309
- LAMP (F-565/525) 309
- Network PCB 310
- PCB MAIN 311
- PCB CONNECT A 312
- POWER-SUPPLY 312
- PCB PSU / PCB NCU 313
- PCB CONNECT C 314
- 5.2.3 SCANNING SECTION 315
- Gear 40 0.6B 315
- ASSY SHAFT S 315
- 3) Open the Guide inner B 316
- Then remove the ROLLER FEED 317
- Flat harness 319
- Frame scanner 319
- Shaft guide 320
- Bracket scanner B 321
- Sensor stopper 322
- Home sensor 322
- CHASSIS FBS 323
- 2) Cut the Cable tie 324
- 3) Disconnect the connector 324
- 4) Cut the Cable tie 325
- GUIDE INNER A 326
- GUIDE OUTER 326
- 4) Remove the PAD SEPARATOR 327
- ADF DRIVE GEARS 328
- APS bracket 329
- Guide inner A 329
- Guide inner B 330
- Spring C Tension 331
- Bracket motor FBS 331
- FBS motor 332
- Solenoid 333
- Cable tie 333
- Bracket solenoid 333
- Clutch(MG) 333
- Motor duplex 334
- Ground wire 335
- Stay pickup 335
- Spring clutch 335
- FRAME DRIVE GEARS 336
- Cover bracket transfer 338
- Guide paper transfer A 338
- Sheet transfer 338
- ROLLER REGISTER 339
- SENSOR TRAYS 340
- SENSOR JAMC1 341
- COVER SWITCH 341
- SENSOR PSS 342
- ASSY FUSER 343
- SENSOR PDS / DPS 344
- ROLLER EXIT 344
- 2) Remove the PAD PRESSURE 345
- SENSOR JAMC2 346
- SENSOR PES2 347
- ROLLER FEED 2ND (2nd CST) 347
- Plate frame B 348
- Chassis 2nd 348
- PLATE FRAME B GEARS (2nd CST) 349
- SPRING CLUTCH (2nd CST) 350
- SOLENOID (2nd CST) 350
- SENSOR OPEN2 351
- ROLLER FEED DUPLEX 352
- ROLELR FFED DUPLEX 353
- TONER SENSOR 1, 2 (TS1, TS2) 354
- Bracket toner sensor B 355
- Bracket toner sensor A 356
- SENSOR PES1 357
- Film harness 359
- Stay LED 359
- Adjustment procedure 361
- 5.3.3 Registration adjustment 363
- 5.3.4 Zoom adjustment 367
- Roller separator 371
- Cover separator 371
- Mirror A 372
- Mirror C 372
- Mirror B 372
- Cover scanner 372
- 6 Options 373
- 6.2 Second paper cassette 375
- 6.3 Page Counter 377
- Connection board B 378
- Relay cable 378
- 6.4 PCL printer controller 379
- 6.5 Second phone line kit 380
Související produkty a manuály pro Multifunkční zařízení Muratec F-565
Multifunkční zařízení Muratec MFX-1200 Specifikace
(205 stránky)
(205 stránky)
Multifunkční zařízení Muratec F-360 Specifikace
(290 stránky)
(290 stránky)
Multifunkční zařízení Muratec MFX-2590 Specifikace
(279 stránky)
(279 stránky)
(193 stránky)
(93 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce